dialogic d300语音卡驱动重装后启动报错问题解决方法

dialogic d300 驱动重装后 dlstart 报错解决

问题描述：dlstart 后如下报错

[root@BJAPQ091 data]#dlstop

Stopping Dialogic Services…

Stopping Clocking Daemon:[ 纭�畾 ]

Stopping ClockingServer:[ 纭�畾 ]

Stopping Telephony System Monitor:[ 纭�畾 ]

Stopping Dialogic(R) board(s).

Deleting SW devices ….

Deleting SW devices Done

genload[17226]: Warning – Insufficient power overriden for the PCI Express board at bus 7, slot 0.

Stopping Timeslot Doler:[ 纭�畾 ]

Stopping Device Mapper:[ 纭�畾 ]

Shutting Down OAM Event Service:[ 纭�畾 ]

Stopping Dialogic Runtime Tracing Server:[ 纭�畾 ]

[root@BJAPQ091 ~]# dlstart

Starting Dialogic Services…

Starting Dialogic Runtime Tracing Server:[ 纭�畾 ]

Warning: You have chosen a Springware board to be the Primary clock master

Clock fallback will not be supported in this configuration

Starting OAM Event Service:[ 纭�畾 ]

Starting Device Mapper:[ 纭�畾 ]

Starting Timeslot Doler:[ 纭�畾 ]

Starting Telephony System Monitor:[ 纭�畾 ]

Starting Clocking Server:[ 纭�畾 ]

Starting Dialogic(R) board(s).

Dialogic(R) Generic Downloader Version 6.00 (Build 1)

Using /usr/dialogic/cfg/dialogic.cfg to configure Dialogic Boards

genload[18399]: Warning – Insufficient power overriden for the PCI Express board at bus 7, slot 0.

System Download ……..

Warning: Clock signals not detected on sec. lines

……………………………………………………………………

D/300JCT-E1 (PCI ID 0) Download .. spisctr4 Firmware Version 6.70 Build 0024

1 Dialogic?Board Successfully Installed

Dialogic(R) SCSA Transmit Timeslot Assignment Program

sctsassign:The Start TS is: 0 and Total Number of TS: 60

dxxxB1 : Failed open in sctsdtdxag.c: No such file or directory

dxxxB2 : Failed open in sctsdtdxag.c: No such file or directory

dxxxB3 : Failed open in sctsdtdxag.c: No such file or directory

dxxxB4 : Failed open in sctsdtdxag.c: No such file or directory

dxxxB5 : Failed open in sctsdtdxag.c: No such file or directory

dtiB1 : Failed open in sctsdtdxag.c: No such file or directory

dxxxB6 : Failed open in sctsdtdxag.c: No such file or directory

dxxxB7 : Failed open in sctsdtdxag.c: No such file or directory

dxxxB8 : Failed open in sctsdtdxag.c: No such file or directory

Add SW Devices ….

REGVOX: #

REGVOX: # Dialogic Generic Configuration File

REGVOX: #

REGVOX: # Total number of virtual boards – 9

REGVOX: #

REGVOX:

REGVOX: #

REGVOX: # Board Type – D/300JCT-E1

REGVOX: #

REGVOX: dxxxB1 4 7000010 C FBFE0000 2000 20 SPAN 50004

REGVOX: dxxxB2 4 7000010 C FBFE2000 2000 20 SPAN 50005

REGVOX: dxxxB3 4 7000010 C FBFE4000 2000 20 SPAN 50006

REGVOX: dxxxB4 4 7000010 C FBFE6000 2000 20 SPAN 50007

REGVOX: dxxxB5 4 7000010 C FBFE0000 2000 0 SPAN 50008

REGVOX: dtiB1 30 7000010 T FBFE0000 2000 0 E1SPAN 50009

REGVOX: dxxxB6 4 7000010 C FBFE2000 2000 0 SPAN 50010

REGVOX: dxxxB7 4 7000010 C FBFE4000 2000 0 SPAN 50011

REGVOX: dxxxB8 2 7000010 C FBFE6000 2000 0 SPAN 50012

Add SW Devices Done

Checking for unsupported Dialogic boards:

usbu[18448]: Warning – Insufficient power overriden for the PCI Express board at bus 7, slot 0.

Starting Clocking Daemon:[ 纭�畾 ]

Starting fault detection on all Dialogic boards:[ 纭�畾 ]

解决办法：

经过google，发现是因为语音卡驱动加载openib与streams有冲突

（1）关闭应用 epos用户下 grMain -t

（2）root检查是否有安装openib rpm -qa | grep openib

（3）如果有，卸载openib rpm -e openib

（4）检查是否卸载成功 rpm -qa | grep openib

（5）重启机器

（6）root用户下 dlstop

（7）root下 dlstart 查看是否启动成功

（8）epos下 grMain -s -l5 -d5 -w -r 启动应用

参考文档：

Thought I would share this. I recently ran into this issue when trying to start Dialogic on RHEL 4. dlstart would produce the following. Apparently version 6 and older of up2date will load an openib package which conflicts with streams.

SCREEN OUTPUT:

dxxxB1 : Failed open in sctsdtdxag.c: No such file or directory

dtiB1 : Failed open in sctsdtdxag.c: No such file or directory

dxxxB2 : Failed open in sctsdtdxag.c: No such file or directory

dxxxB3 : Failed open in sctsdtdxag.c: No such file or directory

dxxxB4 : Failed open in sctsdtdxag.c: No such file or directory

dxxxB5 : Failed open in sctsdtdxag.c: No such file or directory

dxxxB6 : Failed open in sctsdtdxag.c: No such file or directory

RTF LOG:

#Timestamp #PID #TID #Module #Client #Label #Message

06/23/2009 09:20:55.754 20988 3008342944 OAMSYSLOG ErrorEx DLGTIMESLOTDOLER – Fail to get TDMbus Attr error = 100

06/23/2009 09:20:55.755 20988 3008342944 OAMSYSLOG ErrorEx DLGTIMESLOTDOLER – Fail to get TDMbus Attr error = 100

06/23/2009 09:20:56.249 21260 3086215392 spwrvoice ERR1 dxmain dxxxB1 ::::> dx_open() = -1, open(/dev/dlgn) = -1

06/23/2009 09:20:56.258 21260 3086215392 spwrvoice ERR1 dxmain dxxxB2 ::::> dx_open() = -1, open(/dev/dlgn) = -1

06/23/2009 09:20:56.259 21260 3086215392 spwrvoice ERR1 dxmain dxxxB3 ::::> dx_open() = -1, open(/dev/dlgn) = -1

06/23/2009 09:20:56.261 21260 3086215392 spwrvoice ERR1 dxmain dxxxB4 ::::> dx_open() = -1, open(/dev/dlgn) = -1

06/23/2009 09:20:56.262 21260 3086215392 spwrvoice ERR1 dxmain dxxxB5 ::::> dx_open() = -1, open(/dev/dlgn) = -1

06/23/2009 09:20:56.264 21260 3086215392 spwrvoice ERR1 dxmain dxxxB6 ::::> dx_open() = -1, open(/dev/dlgn) = -1

06/23/2009 09:20:57.375 21327 3086096896 OAMSYSLOG ErrorEx dlgclockdaemon – ConfigTDMBus(): Cannot retrieve TDM bus attributes from Device Mapper for bus id 158570088; 100 returned from dm_getAttributes().

06/23/2009 09:20:57.375 21327 3086096896 OAMSYSLOG ErrorEx dlgclockdaemon – ConfigTDMBus(): FATAL CONFIGURATION ERROR.

06/23/2009 09:20:57.375 21327 3086096896 OAMSYSLOG ErrorEx dlgclockdaemon – Failed to configure the TDM bus; ConfigTDMBus() returned 0x0.

06/23/2009 09:20:58.956 21352 3061984160 OAMIPC Warning OAMTransport – CSocketClientTransport::SendMessage() – m_ClientReceiveSocket.ShutAndCloseSocket failed

06/23/2009 09:20:58.955 21051 2892954528 OAMSYSLOG ErrorEx DLGSPWRFAULTDETECTOR – CNIStatus::init(): Failed to open the DTI device dtiB1

FIND AND FIX:

[root@ares cfg]# lsmod

Module Size Used by

mercd 281204 0

ctimod 28916 1 mercd

streams_dvbmDriver 132616 0

streams_sctmrDriver 29104 0

streams_gpioDriver 21028 0

streams_gncfdDriver 19112 0

streams_dlgnDriver 418536 4 streams_dvbmDriver,streams_sctmrDriver,streams_gpioDriver,streams_gncfdDriver

streams 859756 5 streams_dvbmDriver,streams_sctmrDriver,streams_gpioDriver,streams_gncfdDriver,streams_dlgnDriver

parport_pc 28033 0

lp 15661 0

parport 38153 2 parport_pc,lp

autofs4 26053 0

i2c_dev 14529 0

i2c_core 26305 1 i2c_dev

sunrpc 145061 1

ipt_REJECT 10689 1

ipt_state 5953 17

ip_conntrack 46085 1 ipt_state

iptable_filter 6977 1

ip_tables 23105 3 ipt_REJECT,ipt_state,iptable_filter

cpufreq_powersave 5953 0

ib_srp 39005 0

ib_sdp 61437 0

ib_ipoib 81769 0

inet_lro 13121 1 ib_ipoib

md5 8129 1

ipv6 244833 84 ib_ipoib

rdma_ucm 21189 0

rdma_cm 39937 2 ib_sdp,rdma_ucm

iw_cm 13381 1 rdma_cm

ib_addr 12357 1 rdma_cm

ib_umad 21737 0

ib_ucm 22213 0

ib_uverbs 41833 2 rdma_ucm,ib_ucm

ib_cm 46521 4 ib_srp,ib_ipoib,rdma_cm,ib_ucm

ib_sa 43213 4 ib_srp,ib_ipoib,rdma_cm,ib_cm

ib_mad 39897 3 ib_umad,ib_cm,ib_sa

ib_core 66369 12 ib_srp,ib_sdp,ib_ipoib,rdma_ucm,rdma_cm,iw_cm,ib_umad,ib_ucm,ib_uverbs,ib_cm,ib_sa,ib_mad

button 10705 0

battery 12997 0

ac 8901 0

uhci_hcd 33241 0

e100 36677 0

mii 9281 1 e100

e1000 122837 0

floppy 58193 0

dm_snapshot 22633 0

dm_zero 6337 0

dm_mirror 32969 0

ext3 119753 4

jbd 59865 1 ext3

dm_mod 67049 12 dm_snapshot,dm_zero,dm_mirror

ata_piix 19909 2

libata 105629 1 ata_piix

sd_mod 20801 3

scsi_mod 120525 3 ib_srp,libata,sd_mod

[root@ares cfg]# rpm -qa | grep openib

openib-1.4-1.el4

[root@ares cfg]# rpm -e openib

[root@ares cfg]# rpm -qa | grep openib

Then reboot and all is back to normal. Hope this helps some one else out there.

北京行二号机 dlstart 报错解决